Andreas Hoffmann

Follow
  • Total activity 31
  • Last activity
  • Member since
  • Following 0 users
  • Followed by 0 users
  • Votes 0
  • Subscriptions 1

Activity overview

Latest activity by Andreas Hoffmann

  • Andreas Hoffmann created an article,

    Difference between using a flat surface and a bar for alignment when using a single sensor

    1. Gocator
    2. General

    QuestionWhat is the difference between using a flat surface and a bar for alignment when using a single sensor?Answer Sensor Model All ...

    • Andreas Hoffmann
    • 1 follower
    • 0 comments
    • 0 votes

  • Andreas Hoffmann created an article,

    Difference between alignment and travel calibration

    1. Gocator
    2. User Interface

    QuestionWhat is the difference between alignment and travel calibration?Answer Sensor Model All Firmware V...

    • Andreas Hoffmann
    • Updated
    • 1 follower
    • 0 comments
    • -1 votes

  • Andreas Hoffmann created an article,

    Powering the system with 24VDC when using a Master

    1. Gocator
    2. Hardware

    QuestionCan I power the system with 24VDC when using a Master?Answer Sensor Model All Firmware Version ...

    • Andreas Hoffmann
    • Updated
    • 1 follower
    • 0 comments
    • 0 votes

  • Andreas Hoffmann created an article,

    Calculating the value of Vdata for digital input in active-low set-up

    1. Gocator
    2. General

    QuestionHow do I calculate the value of the Vdata for digital input in the active-low set-up?Answer Sensor Model All ...

    • Andreas Hoffmann
    • 2 followers
    • 0 comments
    • -1 votes

  • Andreas Hoffmann created an article,

    Pulsing the gate signal when using gated trigger mode

    1. Gocator
    2. Hardware

    QuestionDo I have to pulse the gate signal when using gated trigger mode?Answer Sensor Model All Firmware ...

    • Andreas Hoffmann
    • Updated
    • 2 followers
    • 0 comments
    • 1 vote

  • Andreas Hoffmann created an article,

    Laser line flickers after installation

    1. Gocator
    2. Hardware

    QuestionWhy after installation does the sensor not operate correctly (the laser line flickers)?Answer Sensor Model G2xxx ...

    • Andreas Hoffmann
    • Updated
    • 1 follower
    • 0 comments
    • 0 votes

  • Andreas Hoffmann created an article,

    Encoder spacing

    1. Gocator
    2. Configuration

    QuestionHow is encoder spacing defined?Answer Sensor Model All Firmware Version 3.x, 4.x ...

    • Andreas Hoffmann
    • Updated
    • 1 follower
    • 0 comments
    • 0 votes

  • Andreas Hoffmann created an article,

    Encoder resolution definition

    1. Gocator
    2. Hardware

    Question How is encoder resolution defined? Answer Sensor Model All Firmware Version 3.x, 4.x SDK Version n/a The encoder resolution is defined in mm/tick in the Gocator web GUI. This...

    • Andreas Hoffmann
    • Updated
    • 2 followers
    • 0 comments
    • 6 votes

  • Andreas Hoffmann created an article,

    Gocator encoder Z signal needed for encoder triggered operation

    1. Gocator
    2. SDK

    QuestionIs the Gocator encoder Z signal needed for encoder triggered operation?Answer Sensor Model All Fir...

    • Andreas Hoffmann
    • Updated
    • 1 follower
    • 0 comments
    • 1 vote

  • Andreas Hoffmann created an article,

    Gocator smoothing filter

    1. Gocator
    2. General

    QuestionHow does the Gocator smoothing filter work?Answer Sensor Model G2xxx Firmware Version ...

    • Andreas Hoffmann
    • 1 follower
    • 0 comments
    • 0 votes